udp-over-tls-pool 0.1.1

Description:

udpovertlspool 0.1.1

udp-over-tls-pool

Network wrapper which transports UDP packets over multiple TLS sessions (or plain TCP connections).
Client-side application listens UDP port and for each sending endpoint it establishes multiple connections to server-side application. Server side application maintains UDP endpoint socket for each group of incoming connections and forwards data to destination UDP socket.
udp-over-tls-pool can be used as a transport for Wireguard or other UDP VPN protocols in cases where plain UDP transit is impossible or undesirable.

:heart: :heart: :heart:
You can say thanks to the author by donations to these wallets:

ETH: 0xB71250010e8beC90C5f9ddF408251eBA9dD7320e
BTC:

Legacy: 1N89PRvG1CSsUk9sxKwBwudN6TjTPQ1N8a
Segwit: bc1qc0hcyxc000qf0ketv4r44ld7dlgmmu73rtlntw




Features

Based on proven TLS security
Uses multiple connections for greater performance
Cross-plaform: runs on Linux, macOS, Windows and other Unix-like systems.

Requirements

Python 3.5.3+

Installation
From PyPI
pip3 install udp-over-tls-pool

From Snap Store

sudo snap install udp-over-tls-pool

Note that binaries installed by snap are named udp-over-tls-pool.server and udp-over-tls-pool.client.
Usage
Server example:
uotp-server -c /etc/letsencrypt/live/example.com/fullchain.pem \
-k /etc/letsencrypt/live/example.com/privkey.pem \
127.0.0.1 26611

where 26611 is a target UDP service port. By default server accepts connections on port 8443.
Client example:
uotp-client -a 0.0.0.0 example.com 8443

where 0.0.0.0 is a listen address (default is localhost only) and example.com 8443 is uotp-server host address and port. By default client listens UDP port 8911.
See Synopsis for more options.
Using as a transport for VPN
This application can be used as a transport for UDP-based VPN like Wireguard or OpenVPN.
In case when udp-over-tls-pool server address is covered by routing prefixes tunneled through VPN (for example, if VPN replaces default gateway), udp-over-tls-pool traffic must be excluded. Otherwise connections from uotp-client to uotp-server will be looped back to tunnel. There are at least two ways to resolve that loop.
Excluding uotp-client traffic with a static route
Classic solution is to define specific route to host with udp-over-tls-pool server. Here is an example Wireguard configuration for Linux:
[Interface]
Address = 172.21.123.2/32
PrivateKey = XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
PreUp = ip route add 198.51.100.1/32 $(ip route show default | cut -f2- -d\ )
PostDown = ip route del 198.51.100.1/32

[Peer]
PublicKey = YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY
Endpoint = 127.0.0.1:8911
AllowedIPs = 0.0.0.0/0

where 198.51.100.1 is an IP address of host with uotp-server.
Such solution should work on all platforms and operating systems, though it leaves all other traffic to uotp-server host unprotected.
Excluding uotp-client traffic with rule-based routing
Some VPN tunnels use rule-based routing on Linux to exclude own packets from tunnel itself. For example, Wireguard started with wg-quick command uses netfilter mark to distinguish tunnel carrier packets. uotp-client is capable to mark own TCP/TLS packets with nfmark as well. To enable this feature you may run uotp-client like this:
uotp-client --resolve-once --mark 0xca6c example.com 8443

where 0xca6c is default fwmark for Wireguard set by wg-quick. You may check this value with wg show INTERFACE fwmark. Once this is enabled no additional for Wireguard configuration is required.
Note that to use netfilter marks uotp-client has to be run as superuser or process has to be started with CAP_NET_ADMIN capability. You may set this capability for a process running as restricted user with systemd service file like one below:
# /etc/systemd/system/uotp-client.service
[Unit]
Description=UDP over TLS pool client
After=syslog.target network.target

[Service]
Type=notify
User=uotp-client
AmbientCapabilities=CAP_NET_ADMIN
ExecStart=/usr/local/bin/uotp-client --resolve-once --mark 0xca6c example.com 8443
Restart=always
KillMode=process

[Install]
WantedBy=multi-user.target

Synopsis
Server:
$ uotp-server --help
usage: uotp-server [-h] [-v {debug,info,warn,error,fatal}] [-l FILE]
[-a BIND_ADDRESS] [-p BIND_PORT] [--no-tls] [-c CERT]
[-k KEY] [-C CAFILE]
dst_address dst_port

UDP-over-TLS-pool. Server-side application.

positional arguments:
dst_address target hostname
dst_port target UDP port

optional arguments:
-h, --help show this help message and exit
-v {debug,info,warn,error,fatal}, --verbosity {debug,info,warn,error,fatal}
logging verbosity (default: info)
-l FILE, --logfile FILE
log file location (default: None)

listen options:
-a BIND_ADDRESS, --bind-address BIND_ADDRESS
TLS/TCP bind address (default: 0.0.0.0)
-p BIND_PORT, --bind-port BIND_PORT
TLS/TCP bind port (default: 8443)

TLS options:
--no-tls do not use TLS (default: True)
-c CERT, --cert CERT use certificate for server TLS auth (default: None)
-k KEY, --key KEY key for TLS certificate (default: None)
-C CAFILE, --cafile CAFILE
authenticate clients using following CA certificate
file (default: None)

Client:
$ uotp-client --help
usage: uotp-client [-h] [-v {debug,info,warn,error,fatal}] [-l FILE]
[-a BIND_ADDRESS] [-p BIND_PORT] [-e EXPIRE] [-n POOL_SIZE]
[-B BACKOFF] [-w TIMEOUT] [--no-tls] [-c CERT] [-k KEY]
[-C CAFILE]
[--no-hostname-check | --tls-servername TLS_SERVERNAME]
dst_address dst_port

UDP-over-TLS-pool. Client-side application.

positional arguments:
dst_address target hostname
dst_port target port

optional arguments:
-h, --help show this help message and exit
-v {debug,info,warn,error,fatal}, --verbosity {debug,info,warn,error,fatal}
logging verbosity (default: info)
-l FILE, --logfile FILE
log file location (default: None)

listen options:
-a BIND_ADDRESS, --bind-address BIND_ADDRESS
UDP bind address (default: 127.0.0.1)
-p BIND_PORT, --bind-port BIND_PORT
UDP bind port (default: 8911)
-e EXPIRE, --expire EXPIRE
UDP session idle timeout in seconds (default: 120.0)

pool options:
-n POOL_SIZE, --pool-size POOL_SIZE
connection pool size (default: 8)
-B BACKOFF, --backoff BACKOFF
delay after connection attempt failure in seconds
(default: 5.0)
-w TIMEOUT, --timeout TIMEOUT
server connect timeout in seconds (default: 4.0)

TLS options:
--no-tls do not use TLS (default: True)
-c CERT, --cert CERT use certificate for client TLS auth (default: None)
-k KEY, --key KEY key for TLS certificate (default: None)
-C CAFILE, --cafile CAFILE
override default CA certs by set specified in file
(default: None)
--no-hostname-check do not check hostname in cert subject. This option is
useful for private PKI and available only together
with "--cafile" (default: False)
--tls-servername TLS_SERVERNAME
specifies hostname to expect in server TLS certificate
(default: None)