Last updated:
0 purchases
pyscrlink 0.2.8
pyscrlink
Pyscrlink is a Scratch-link for Linux.
Scratch-link is a software module which connects
Scratch to Bluetooth devices such as
micro:bit. However, as of October 2020, it only works
on Windows and MacOS, and Linux operating systems can not connect Scratch and
micro:bit.
Pyscrlink allows you to connect Scratch and bluetooth devices with the Linux
OSes. It uses the Linux Bluetooth protocol stack Bluez
and bluepy to handle Bluetooth Low Energy
(BLE) connections. It has been reported that pyscrlink connects Scratch 3.0 with
micro:bit, LEGO WeDo, LEGO Boost and toio.
Until version v0.2.5, pyscrlink supported Bluetooth Classic protocol using
pybluez. Unfortunately, pybluez is not
well maintained and caused technical troubles. Then Bluetooth Classic protocol
support is dropped from pyscrlink. This means that LEGO Mindstorm EV3 can not
be connected with pyscrlink. Bluetooth Classic support is the improvement
opportunity of pyscrlink.
To use websockets, pyscrlink requires python version 3.6 or later. If your
system has python older than version 3.6, install newer version. If your
system has python 3 explicit command names python3 and pip3, use them in the
steps below.
Pyscrlink was launched in 2019 as "bluepy-scratch-link". This was a small task
dedicated to micro:bit and bluepy for BLE connection. After many contributions,
it expanded coverage to pybluez with other devices for Bluetooth connectivity.
It was misleading that the name "bluepy-scratch-link" indicates that it depends
only on bluepy. As of October 2020, name of the project has been changed from
"bluepy-scratch-link" to "pyscrlink" to avoid confusion.
Confirmed Environments
The instructions below was confirmed with following devices and distros.
Trial with other distros and feed-backs will be appreciated.
Pyscrlink was confirmed with following devices, Linux distros and browsers.
Devices:
micro:bit
Linux distros:
Arch Linux
Browsers:
Firefox
Chromium
It was reported that pyscrlink (former bluepy-scratch-link) working with
following devices and Linux distros.
Devices:
LEGO WeDo by @zhaowe, @KingBBQ
LEGO Boost and compatible devices by @laurentchar, @miguev, @jacquesdt, @n3storm
toio by @shimodash
Linux distros:
Raspbian by @chrisglencross
Ubuntu 16.04 @jacquesdt
Ubuntu Studio 20.04 @miguev
Debian 11 @n3storm
Installation
Prepare Bluetooth/BLE controller.
Confirm that your Linux PC has a Bluetooth controller with BLE support.
Bluetooth 4.0 controller supports BLE. If your PC does not have it, need
to plug USB Bluetooth 4.0 adapter.
Note: BLED112 USB dongle with Bluegiga BGAPI is not supported.
Install required packages.
Ubuntu
$ sudo apt install bluez libbluetooth-dev libnss3-tools libcap2-bin libglib2.0-dev
Arch
$ sudo pacman -S bluez bluez-utils nss libcap
Install python modules.
$ pip install pyscrlink
Or if your system has python3 command,
$ pip3 install pyscrlink
Set bluepy-helper capability.
$ bluepy_helper_cap
Set capacbility 'cap_net_raw,cap_net_admin' to /usr/lib/python3.8/site-packages/bluepy-1.3.0-py3.8.egg/bluepy/bluepy-helper
The command above requires super user privilege. It may request to input
super user password.
For micro:bit, install Scratch-link hex on your device.
Download and unzip the micro:bit Scratch Hex file.
Flash the micro:bit over USB with the Scratch Hex File, you will see the
five character name of the micro:bit scroll across the screen such as
'zo9ev'.
Usage
Start scratch-link python script.
$ scratch_link
If your device is toio, add "-s 1" option to the scratch_link command. It
allows the toio Do Visual Programming to connect to toio automatically.
Connect scratch to the target device such as micro:bit:
Open FireFox or Chrome. (Make sure to run as the same user for scratch-link python script.)
Access Scratch 3.0 and create your project.
Select the "Add Extension" button.
Select the extension for your device (e.g., micro:bit) and follow the prompts to connect.
Build your project with the extension blocks.
In Case You Fail to Connect
If Scratch says "Make sure you have Scratch Link installed" but you are sure
that scratch-link python script is running, check that Firefox or Chrome
allows local server certificate.
Open Firefox or Chrome and access https://device-manager.scratch.mit.edu:20110/. You will see a security risk warning.
In Firefox: Click "Advanced" and click "Accept Risk and Continue".
In Chrome: type the special bypass keyword thisisunsafe.
Immediately, you will see "Failed to open a WebSocket connection". This is expected.
If device scan fails, check systemd bluetooth service status.
systemctl status bluetooth.service
If the service is not working, refer guide of your distro to set it up.
If the service is working, also check that /etc/bluetooth/main.conf sets AutoEnable=true.
If device scan still fails, use -r option to retry device scan.
The command line below does device scan twice. Each scan takes 10 seconds.
$ scratch_link -r 2
It would be good to use -s option together to reduce each scan duration.
The command line below does 3 seconds device scan twice.
$ scratch_link -r 2 -s 3
If scratch_link.py says "failed to connect to BT device: [Errno 13] Permission denied",
make sure to pair the bluetooth device to your PC before connecting to Scratch.
To connect to multiple devices at the same time, make all the target devices
ready for scan at the first device scan. This is important for toio. The toio
allows a single project to connect to two toio devices.
When the second device was prepared after the first device was connected, device scan can not find the second device.
To scan and find the second device, disconnect connections for the first device beforehand.
Issus Reporting
Please file issues to GitHub issue tracker.
Releases
Release 0.2.8
Supported Microbit More v2
Release 0.2.7
Supported Snap Firefox and Chromium
Added -r option to retry BLE scan
Release 0.2.6
Removed Bluetooth Classic and LEGO Mindstorm EV3 support
Release 0.2.5
Fixed handling of multiple UUIDs for LEGO Boost
Release 0.2.4
Added -s option to specify BLE scan duration
Improved README.md
Release 0.2.3
Fixed eternal loop caused by hostname resolve failure
Release 0.2.2
Supported multiple device connections for toio
Improved session closure handling
Release 0.2.1
Added libglib to required package list in README.md
Improved setcap and getcap tool finding
Release 0.2.0
Latency issue fix for BLE devices' write characteristics
Release 0.1.0
Initial release
For personal and professional use. You cannot resell or redistribute these repositories in their original state.
There are no reviews.