use-minimon-dj 0.1.0

Description:

useminimondj 0.1.0

Use-Minimon
This package is an in-house tool that makes it easy to use Renesas MiniMonitor.
Using the MiniMonitor is a cumbersome thing.
You have to type a couple of 'Y' and hex addresses just to flash a binary.
This package is a simple script to automatically answer questions of MiniMonitor
and send a binary file to MiniMonitor to flash it into HyperFlash memory.
Installation
Use-Minimon is published on PyPI
and can be install from there
pip install -U use-minimon-dj

How to Use


Bringing up MiniMonitor stored in QSPI NOR Flash memory
These DIP switches and jumper must be configured like this:
SW1 = OFF
SW6 = ON ON OFF ON (A57, QSPI, DDR3200)
JP1 = 1-2 Short



Turning on the target board
Push the switch No. 8 to turn on the target board.
R-Car Gen3 Sample Loader V5.08 2018.10.22
For Salvator , Kriek , and StarterKit.(R-CarH3/R-CarM3)
Board Judge : Used Board-ID
DDR_Init : boardcnf[8] Salvator (H3SIP_VER2.0/3.0-2rank)
INITIAL SETTING : Starter Kit Premier / R-Car H3 ES3.0
CPU / BOOT MODE : AArch64 CA57-CPU0 / CA57 Boot Mode (MD15:AArch64)
DRAM : LPDDR4 DDR3200 / 8GB_2RANK
DEVICE : QSPI Flash(S25FS128) at 40MHz DMA
BOOT : Normal Boot
BACKUP : DDR Cold Boot
jump to 0xE6330000

R-Car Gen3 MiniMonitor V5.08 2018.10.22
Work Memory : SystemRAM Board Judge : Used Board-ID
Board Name : Starter Kit Premier
Product Code : R-Car H3 ES3.0

>



Configuring DIP switches to enable HyperFlash memory
SW1 = ON
SW6 = ON ON ON ON (A57, HyperFlash 80 MHz, DDR3200)



Executing mm-flashing command like so on your workstation
$ mm-flashing crbl2 crbl2.srec



The output of the target board will be something like this
R-Car Gen3 Sample Loader V5.08 2018.10.22
For Salvator , Kriek , and StarterKit.(R-CarH3/R-CarM3)
Board Judge : Used Board-ID
DDR_Init : boardcnf[8] Salvator (H3SIP_VER2.0/3.0-2rank)
INITIAL SETTING : Starter Kit Premier / R-Car H3 ES3.0
CPU / BOOT MODE : AArch64 CA57-CPU0 / CA57 Boot Mode (MD15:AArch64)
DRAM : LPDDR4 DDR3200 / 8GB_2RANK
DEVICE : QSPI Flash(S25FS128) at 40MHz DMA
BOOT : Normal Boot
BACKUP : DDR Cold Boot
jump to 0xE6330000

R-Car Gen3 MiniMonitor V5.08 2018.10.22
Work Memory : SystemRAM
Board Judge : Used Board-ID
Board Name : Starter Kit Premier
Product Code : R-Car H3 ES3.0

>xls2
===== Qspi/HyperFlash writing of Gen3 Board Command =============
Load Program to Spiflash
Writes to any of SPI address.
Please select,FlashMemory.
1 : QspiFlash (U5 : S25FS128S)
2 : QspiFlash Board (CN2: S25FL512S)
3 : HyperFlash (SiP internal)
Select (1-3)>3
READ ID OK.
Program Top Address & Qspi/HyperFlash Save Address
===== Please Input Program Top Address ============
Please Input : H'51000000

===== Please Input Qspi/HyperFlash Save Address ===
Please Input : H'740000
Work RAM(H'50000000-H'53FFFFFF) Clear....
please send ! ('.' & CR stop load)
SPI Data Clear(H'FF) Check : OK
SAVE SPI-FLASH....... complete!

======= Qspi/HyperFlash Save Information =================
SpiFlashMemory Stat Address : H'00740000
SpiFlashMemory End Address : H'007FF9C7
===========================================================